1 ZXT-300EU (Z-Wave-to-AV IR Extender) Z-URCTM 550EU (Z-Wave Enabled Universal Remote Control)
10 Note 2: XpressZetupTM cannot support “Multi-Channel Device”, please refer to [Adding Device to the Network] and [Adding Device/End-point to a gro
11 Note 2: This process will only remove the group devices from its assigned group but will not exclude it from the network. Group Operation Aft
12 Scene Control Z-Wave Scenes are used for setting up multiple devices in the same way as a group but in addition to groups, scenes also control d
13 6 Press • “OK" LED flashes once then turns off • “LED_B" off • The current status of the device will be learned and saved to a scene successf
14 • “LED_A" flashes slowly 3 Select a scene number from 1 to 16 (1-8 or 1-8) • “OK" LED flashes once then turns off • “LED_A" off • Scen
15 3 Press the program button on the target device • “OK" LED flashes once then turns off • “LED_B" off • Device inclusion completed Note 1: Th
16 Note 1: Your target device must be included in the network before this setup procedure, please refer to [Adding Device to the Network] section.
17 Assign Association for Two Devices The Z-URCTM 550EU can be used to assign one device to automatically interact directly with another device.
18 Removing Device/End-point from an Association Group Step Setup Key LED Indication Status 1 Press in Advance Setup • The “OK" light turns on
19 Deleting an Association Group Step Setup Key LED Indication Status 1 Press in Advance Setup • The “OK" light turns on 2 Press • “OK" LE
2 Table of Contents Introduction... 4 Glossary ...
20 Add/Delete All-On/All- Off functions If desired, specific devices can be setup to ignore the All-On and All-Off commands. The four possible resp
21 Adding Devices to All Control Step Setup Key LED Indication Status 1 Press in Advance Setup • The “OK" light turns on 2 Press and hold the
22 Change Device Configuration This function is used to modify the parameter of the Z-Wave device via the configuration command class. Look up the
23 Advanced Z-Wave Network Setups Copying All Network and Device Information to a Secondary Controller You can add a secondary controller to your
24 Copying Network Information to a Secondary Controller You can add a secondary controller to your network and copy all of your primary controller
25 Transferring All Network and Device Information to a New Primary Controller (Primary Shift) You can transfer all of your controller information
26 Transferring Only Network Information to a New Primary Controller (Primary Shift) You can just transfer network information to another remote so
27 Replicating All Network and Device Information from a Primary Controller to Your Z-URCTM 550EU (“Learning Mode") Your Z-URCTM 550EU can: • C
28 Listening Mode There are multiple usages by entering this mode: • Version command class: To get application software version, the Z-Wave protoc
29 Resetting Your Network You can reset your Z-URCTM 550EU to clear all Z-Wave network and device information by the following steps: Step Setup
3 Add/Delete Devices ... 32 Add/Remove Device to/from a Simple AV channel 34 IR Code Setup ...
30 ZXT-300EU Operations Before using the ZXT-300EU, please read the [INSTALLATION] if it is needed to mount the ZXT-300EU to a wall. Power up the Z
31 ZXT-300EU Information Change Z-Wave-to-IR Channel (EP) on ZXT-300EU Step Setup Key LED Indication Status on ZXT-300EU 1 Press and hold PROG but
32 Add/Delete Devices Adding Device to the Network Step Setup Key LED Indication Status on Z-URCTM 550EU LED Indication Status on ZXT-3
33 Deleting Device from the Network Step Setup Key LED Indication Status on Z-URCTM 550EU LED Indication Status on ZXT-300EU 1 Make sure
34 Add/Remove Device to/from a Simple AV channel There are 6 Simple AV Channels in ZXT-300EU, user can assign them to any of the 8 device buttons o
35 Adding Device to a Simple AV channel Step Setup Key LED Indication Status on Z-URCTM 550EULED Indication Status on ZXT-300EU
36 2 Press in Advance Setup area • Back “OK" LED and front “OK" LED turns on - 3 Select a Simple AV Channel by press device key such as • Back “
37 TV. (enter “0", “0",“0", “1" at the front if it’s show 0001) on for each key press 4 Press the PROG button on ZXT-300EU (The code no. has be
38 which you want to transmit the IR signal on for each key press 6 Press • Front “OK" LED flashes once and stays on - 7 Press the PROG button on
39 4 Press • Front “OK" LED flashes once and stays on - 5 Set IR output power level by entering “0" or “1" in the front “0" low power mode “1" hi
4 Z-URCTM 550EU (Z-Wave Enabled Universal Remote Control) ZXT-300EU (Z-Wave-to-AV IR Extender) Operating Instructions Introduction The Z-URCTM
40 AV Command Operation (Z-Wave Simple AV command class) After added ZXT-300EU to Z-URCTM 550EU network, add device to Simple AV channel and Select
41 once which you want to learn the command once and stays on 6 Press the PROG button on ZXT-300EU (make sure the EP is related to the AV device na
42 IR Code Learning on Z-URCTM 550EU (Learn an IR control code from the original remote control to Z-URCTM 550EU then download to ZXT-300EU) Step
43 a flat surface, aimed at each other 1-3 inches apart 9 Press and keep holding the key on your original equipment remote which you want to learn f
44 to your AV device name) 3 Press in Advance Setup • Back “OK" LED and front “OK" LED turns on - 4 Press any device key (e.g. , , or ) • Fro
45 INSTALLATION MOUNTING THE ZXT-300EU TO A WALL MOUNTING LOCATION PRECAUTIONS • Before mounting, check the material and structure of the mounting
46 adjusting the antenna direction before mounting the ZXT-300EU. Note 2: No screws are provided for mounting to a wall. Note 3: Before mounting to
47 WIRELESS INFORMATION Wireless range: This device has an open air line of sight transmission distance of 100 feet which complies with the Z-Wave s
48 AUDIO/VIDEO SETUP AND OPERATION In addition to Z-Wave device and scene control, your Z-URCTM 550EU is also a universal remote which enables you
49 Description of Audio/Video Control Keys The Z-URCTM 550EU operates up to 8 AV equipments which are accessed by using the SHIFT key and TV or DVD
5 Glossary Device or Node Z-Wave enabled device that can be controlled by the Z-URCTM. Inclusion Add a Z-Wave device to the network. Exclusion De
50 Return, Cancel or Exit Selects the Electronic Program Guide while in SAT/CBL mode also INFO when in shift mode Mute the audio Scrolls through
51 Green button when in SAT/CBL and TV modes also disc menu for DVD when in shift mode Yellow button when in SAT/CBL and TV modes also zoom when i
52 Suggestions: • If you cannot find a correct Device Code for your equipment, refer to AV Equipment Selection by Searching through the Library. •
53 L IMPORTANT − If the power on/off function of your device is not infra-red controlled, you need to follow steps 2 to 6 above and start searchin
54 5 Press a desired key once and release on the Z-URCTM 550EU which you want to learn the command. The green indicator will flash once then stay l
55 Punch Through Punch Through Channel Punch through channel allows you to operate channel up and down without having to switch the device modes re
56 Macro Power Macro Power allows you to turn two of your A/V equipment on/off simultaneously. To activate the macro power setting: 1. Press desir
57 Restore Factory Settings 1 Press and hold "CH+" and "VOL-" keys on the remote simultaneously for 3 seconds until you the ind
58 also being a standard universal remote that can control up to 8 AV equipments. Your Z-URCTM truly turns your living room into your whole houses
59 Q Why do I need a different module for outdoor lighting? A The outdoor module is designed to withstand various weather conditions including hea
6 Z-URCTM 550EU Operations Welcome to the world of home automation, your Z-URCTM 550EU will be able to control all the Z-Wave products around your
60 AV Control Frequently Asked Questions Q My Z-URCTM does not work at all! A Check your A/V device, if the device's main switch is turned of
61 TECHNICAL SPECIFICATIONS Model No. BW8332 V1 (Z-URCTM 550EU) RF Frequency 868.42MHz (EU) IR Frequency Up to 455kHz IR Learning Max 100 comma
62 Z-URCTM 550EU Z-Wave device type Basic Device Class: BASIC_TYPE_CONTROLLER Generic Device Class: GENERIC_TYPE_GENERIC_CONTROLLER Specific Devic
63 COMMAND_CLASS_POWERLEVEL NO YES COMMAND_CLASS_MULTI_CHANNEL_V2 NO YES You can record down your device code under the below table for future
64 WARNINGS Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
7 Configurations Please open the configuration compartment then you can see the Z-URCTM 550EU setup keys (Figure 2). Figure 2 Setup Keys of th
8 Description of Function Keys Keys Functions The All-On and All-Off keys are used for turns on or off all Z-Wave devices in the device database.
9 This Remove key is used in the Advance Setup to: • Remove a device from a group; • Remove a device from an association group; • Remove a devi
Commentaires sur ces manuels